LAMINATED TIMBER,LAMINATED VENEER,CROSS LAMINATED,PARALLEL STRAND,LAMINATED STRAND,FINGER JOINT

LAMINATED TIMBER:-

Glued laminated timber (glulam) is composed of several layers of dimensional timber glued together with moisture-resistant adhesives, creating a large, strong, structural member that can be used as vertical columns or horizontal beams. Glulam can also be produced in curved shapes, offering extensive design flexibility.

LAMINATED VENEER

Laminated Veneer lumbers(LVL) is produced by bonding thin wood veneers together in a large billet. The grain of all veneers in the LVL billet is parallel to the long direction. The resulting product features enhanced mechanical properties and dimensional stability that offer a broader range in product width, depth and length than conventional lumber. LVL is a member of the structural composite lumber (SCL) family of engineered wood products that are commonly used in the same structural applications as conventional sawn lumber and timber, including rafters, headers, beams, joists, rim boards, studs and columns.

CROSS LAMINATED

Cross Laminated Timber (CLT) is a versatile multi-layered panel made of lumber. Each layer of boards is placed cross-wise to adjacent layers for increased rigidity and strength. CLT can be used for long spans and all assemblies, e.g. floors, walls or roofs. CLT has the advantage of faster construction times as the panels are manufactured and finished off site and supplied ready to fit and screw together as a flat pack assembly project.

PARALLEL STRAND

Parallel strand lumber (PSL) consists of long veneer strands laid in parallel formation and bonded together with an adhesive to form the finished structural section. A strong, consistent material, it has a high load carrying ability and is resistant to seasoning stresses so it is well suited for use as beams and columns for post and beam construction, and for beams, headers, and lintels for light framing construction. PSL is a member of the structural composite lumber (SCL) family of engineered wood products.

LAMINATED STRAND

Laminated strand lumber (LSL) and oriented strand lumber (OSL) are manufactured from flaked wood strands that have a high length-to-thickness ratio. Combined with an adhesive, the strands are oriented and formed into a large mat or billet and pressed. LSL and OSL offer good fastener-holding strength and mechanical connector performance and are commonly used in a variety of applications, such as beams, headers, studs, rim boards, and millwork components. These products are members of the structural composite lumber (SCL) family of engineered wood products. LSL is manufactured from relatively short strands—typically about 1 foot long—compared to the 2 foot to 8 foot long strands used in PSL.

FINGER JOINT

The finger joint is made up of short pieces of wood combined to form longer lengths and is used in doorjambs, mouldings and studs. It is also produced in long lengths and wide dimensions for floors.

BEAMS:-

I- Joists and wood I beams are “I“-shaped structural members designed for use in floor and roof construction. An I-joist consists of top and bottom flanges of various widths united with webs of various depths. The flanges resist common bending stresses, and the web provides shear performance.I-joists are designed to carry heavy loads over long distances while using less lumber than a dimensional solid wood joist of a size necessary to do the same task [1]. As of 2005, approximately half of all wood light framed floors were framed using I-joists [2].

TRUSSES

Roof Trusses and floor trusses are structural frames relying on a triangular arrangement of webs and chords to transfer loads to reaction points. For a given load, long wood trusses built from smaller pieces of lumber require less raw material and make it easier for AC contractors, plumbers, and electricians to do their work, compared to the long 2x10s and 2x12s traditionally used as rafters  and floor joists.

TRANSPARENT WOOD COMPOSITES

Transparents wood composite are new materials, currently only made at the laboratory scale, that combine transparency and stiffness via a chemical process that replaces light-absorbing compounds, such as lignin , with a transparent polymer.

Advantages

Engineered wood products are used in a variety of ways, often in applications similar to solid wood products. Engineered wood products may be preferred over solid wood in some applications due to certain comparative advantages:

  • Because engineered wood is man-made, it can be designed to meet application-specific performance requirements. Required shapes and dimension do not drive source tree requirements (length or width of the tree)
  • Engineered wood products are versatile and available in a wide variety of thicknesses, sizes, grades, and exposure durability classifications, making the products ideal for use in unlimited construction, industrial and home project application.
  • Engineered wood products are designed and manufactured to maximize the natural strength and stiffness characteristics of wood. The products are very stable and some offer greater structural strength than typical wood building materials.
  • Glued laminated timber (glulam) has greater strength and stiffness than comparable dimensional lumber and, pound for pound, is stronger than steel.
  • Some engineered wood products offer more design options without sacrificing structural requirements.
  • Engineered wood panels are easy to work with using ordinary tools and basic skills. They can be cut, drilled, routed, jointed, glued, and fastened. Plywood can be bent to form curved surfaces without loss of strength. And large panel size speeds construction by reducing the number of pieces to be handled and installed.
  • Engineered wood products make more efficient use of wood. They can be made from small pieces of wood, wood that has defects or underutilized species.
  • Wooden trusses are competitive in many roof and floor applications, and their high strength-to-weight ratios permit long spans offering flexibility in floor layouts.
  • Engineered wood is felt to offer structural advantages for home construction.

Disadvantage

  • They require more primary energy for their manufacture than solid lumber.
  • The adhesives used in some products may be toxic. A concern with some resins is the release of formaldehyde in the finished product, often seen with  urea formaldehyde bonded products.
  • Cutting and otherwise working with some products can expose workers to toxic compounds.
  • Some engineered wood products, such as those specified for interior use, may be weaker and more prone to humidity induced warping than equivalent solid woods. Most particle and fiber-based boards are not appropriate for outdoor use because they readily soak up water.

REFERENCE TAKEN FROM WIKIPEDIA